Mô phỏng số ảnh hưởng của tốc độ đúc và mác thép đến chiều dày lớp vỏ đông đặc trong đúc liên tục tại Nhà máy HRC Hòa Phát
Development of a Numerical Model for Predicting Solidified Shell Thickness during Continuous Slab Casting of Different Steel Grades
ĐỖ MINH ĐỨC1, TRẦN QUANG HUY2 và PHẠM QUANG1,*
1. Trường Vật liệu, Đại học Bách khoa Hà Nội, Số 1 Đại Cồ Việt, Hà Nội
2. Công ty CP Thép Hòa Phát Dung Quất, Khu Kinh tế Dung Quất, Quảng Ngãi
*Email: quang.pham@hust.edu.vn
Ngày nhận bài: 24/7/2026, Ngày duyệt đăng: 06/8/2026
TÓM TẮT
Nghiên cứu này xây dựng mô hình mô phỏng số quá trình đông đặc trong đúc liên tục phôi tấm nhằm khảo sát ảnh hưởng của tốc độ đúc và mác thép đến chiều dày lớp vỏ đông đặc trong khuôn kết tinh. Mô hình phần tử hữu hạn được xây dựng trong phần mềm ABAQUS trên cơ sở bài toán kết hợp nhiệt – chuyển vị (Coupled Temperature–Displacement), kết hợp mô hình chuyển pha theo phương pháp enthalpy và mô hình truyền nhiệt tiếp xúc phụ thuộc khe hở (Gap Conductance). Điều kiện mô phỏng được thiết lập từ các thông số vận hành thực tế của dây chuyền đúc liên tục tại Nhà máy HRC Hòa Phát. Ba mác thép SAE1006, SS400 và SPA-H được khảo sát ở ba tốc độ đúc gồm 1,1; 1,2 và 1,4 m/phút. Kết quả mô phỏng cho thấy mô hình có khả năng mô tả sự phân bố trường nhiệt độ, sự phát triển của vùng đông đặc và sự thay đổi của dòng nhiệt trong khuôn kết tinh. Chiều dày lớp vỏ đông đặc tại đầu ra khuôn giảm khi tốc độ đúc tăng đối với cả ba mác thép, đồng thời mô hình phản ánh được sự khác biệt về quá trình đông đặc giữa các mác thép khảo sát. Kết quả nghiên cứu là cơ sở cho việc phát triển các nghiên cứu mô phỏng và tối ưu hóa quá trình đúc liên tục trong các điều kiện công nghệ khác nhau.
Từ khóa: Đúc liên tục; Mô phỏng số; Đông đặc; Chiều dày lớp vỏ đông đặc; Khe hở khí; ABAQUS; Tốc độ đúc.
ABSTRACT
This study presents a numerical simulation model of the solidification process during continuous slab casting to investigate the effects of casting speed and steel grade on the formation of the solidified shell in the mold. A finite element model was developed in ABAQUS based on a coupled temperature–displacement analysis, incorporating the enthalpy method for phase transformation and a gap conductance model to describe the evolution of interfacial heat transfer during solidification. The simulation conditions were established using the actual operating parameters of the continuous casting line at Hoa Phat HRC Plant. Three steel grades (SAE1006, SS400 and SPA-H) were investigated at casting speeds of 1.1, 1.2 and 1.4 m/min. The simulation results demonstrate that the proposed model can successfully reproduce the temperature field, solidification region and heat flux distribution in the mold. The solidified shell thickness at the mold exit decreases with increasing casting speed for all investigated steel grades, while differences in shell growth among the steel grades are also captured by the model. The developed model provides a useful basis for further numerical studies and process optimization of continuous casting under different operating conditions.
Keywords: Continuous casting; Numerical simulation; Solidification; Solidified shell thickness; Gap Conductance; ABAQUS; Casting speed.
.jpg)
.jpg)